Model No. PATL49708.0Serial No.Write the serial number in the spaceabove for future reference.CAUTIONRead all precautions and instruc-tions in this ma
108. Remove the plastic ties from the Right Handrail(33) and the Left Handrail (not shown). If neces-sary, press the Cage Nuts (105) back into place.W
111110. Attach the Latch Housing (48) and the LatchHousing Spacer (109) to the Left Upright (53)with two #10 x 1" Tek Screws (112); start bothTek
1212. See the lower drawing. Position the Uprights(53, 54) so that the Frame (51) is centered be-tween them.Firmly tighten the two M10 x 60mm Patch Bo
16. Make sure that all parts are properly tightened before you use the treadmill. Keep the included hex keysin a secure place. One hex key is used to
14OPERATION AND ADJUSTMENTTHE PRE-LUBRICATED WALKING BELTYour treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Nev
15KeyClipCONSOLE DIAGRAMFEATURES OF THE CONSOLEThe treadmill console offers a selection of featuresdesigned to make your workouts more effective. When
16HOW TO TURN ON THE POWERIMPORTANT: If the treadmill has been exposed tocold temperatures, allow it to warm to room tem-perature before turning on th
17The lower left display—As you exercise, thelower left display canshow the elapsed timeand the distance that youhave walked or run. Inaddition, the d
18HOW TO USE A PRESET WORKOUT1. Insert the key into the console.See HOW TO TURN ON THE POWER on page 16.2. Select one of the six preset workouts.To se
19THE INFORMATION MODEThe console features an information mode that keepstrack of treadmill usage information and allows you toselect a unit of measur
TABLE OF CONTENTSWARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20HOW TO FOLD AND MOVE THE TREADMILLHOW TO FOLD THE TREADMILL FOR STORAGEBefore folding the treadmill, adjust the incline to thelowest position. If yo
21HOW TO LOWER THE TREADMILL FOR USE1. Hold the frame with your right hand as shown. Pull the latchknob to the left and hold it. Pivot the frame down
22TROUBLESHOOTINGMost treadmill problems can be solved by following the steps below. Find the symptom that applies, andfollow the steps listed. If fur
23Locate the Reed Switch (89) and the Magnet (62) onthe left side of the Pulley (71). Turn the Pulley until theMagnet is aligned with the Reed Switch.
24PROBLEM: The walking belt is off-center or slips when walked onSOLUTION: a. If the walking belt has shifted to the left, first re-move the key and U
25These guidelines will help you to plan your exerciseprogram. For detailed exercise information, obtain areputable book or consult your physician. Re
2612M10 x 60mm Patch Bolt24 M10 x 75mm Bolt32M4.2 x 13mm Tek Screw4 13 M4.2 x 16mm Screw56M8 Star Washer61Latch Warning Decal72M5 Star Washer86M8 x 15
27Key No. Qty. Description Key No. Qty. Description101 2 Front Roller Washer102 3 M4.2 x 18mm Screw103 1 Console Fan104 2 M10 x 58mm Bolt105 2 Cage Nu
EXPLODED DRAWING A—Model No. PATL49708.0 R0809A9317818651766728628938393631462525252575755625716828186119442729553621422129603619422744191978644504141
EXPLODED DRAWING B—Model No. PATL49708.0 R0809A6620654747475721214242211088710423104725892824049100343844793430593812712190123125372099123126201221308
3IMPORTANT PRECAUTIONS1. Before beginning any exercise program, con-sult your physician. This is especially impor-tant for persons over age 35 or pers
EXPLODED DRAWING C—Model No. PATL49708.0 R0809A8010235411531419111149481033228877242398857710101077101010108485710510552496326133243106696970163512063
31EXPLODED DRAWING D—Model No. PATL49708.0 R0809A159173412444444444116116117110113119981138411011811998103
Part No. 276609 R0809A Printed in China © 2009 ICON IP, Inc.LIMITED WARRANTYThe ICON Authorized Dealer (Dealer) warrants this product to be free from
420. Do not attempt to raise, lower, or move thetreadmill until it is properly assembled. (SeeASSEMBLY on page 6 and HOW TO FOLDAND MOVE THE TREADMILL
5Thank you for selecting the new PROFORM®485CROSSWALK treadmill. The 485 CROSSWALK tread-mill offers a selection of features designed to make yourwork
ASSEMBLYAssembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do notdispose of the packing materials un
72. Have a second person hold the Base (52) in theposition shown.Identify the Right Upright (54) which has asquare hole near the lower end.Hold the Ri
84. Position the Base (52) as close to the front of thetreadmill as possible, as shown.See the upper inset drawing. Locate the wiretie in the lower en
96. See the left inset drawing in step 5. Identifythe outer side of the remaining Frame Spacer(11).Hold the Frame Spacer (11) between the LeftUpright
Kommentare zu diesen Handbüchern