www.iconeurope.com CAUTIONRead all precautions and instruc-tions in this manual before using this equipment. Save this manual for future reference.
108. Identify the Right Handrail (64). Remove the tie from the Right Handrail. If necessary, press the M8 Cage Nut (85) back into place. Hold the
1110. Start an M8 x 25mm Bolt (5) and two 5/16" x 5/8" Screws (79) with two M8 Star Washers (6) into the Right Upright (76) and the Right
1211. Slide the Right Upright Cover (89) up against the Right Handrail (64). Attach the Right Upright Cover with two M4.2 x 16mm Screws (56). Be care
1313. Attach the Latch Bracket (99) on the end of the Storage Latch (97) to the Base (74) with two 3/8" x 2" Bolts (67) and two 3/8" Nu
14HOW TO PLUG IN THE POWER CORDThis product must be earthed. If it should malfunc-tion or break down, earthing provides a path of least resistance for
15FEATURES OF THE CONSOLE The treadmill console offers an impressive array of features designed to make your workouts more effec-tive and enjoyable. W
16HOW TO TURN ON THE POWERIMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem-perature before turning on t
175. Change the incline of the treadmill as desired. To change the incline of the treadmill, press the Incline increase or decrease buttons or on
18HOW TO USE A CALORIE WORKOUT1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 16. 2. Select a calorie workout. To se
19HOW TO USE A PERFORMANCE WORKOUT1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 16. 2. Select a performance workout.
2WARNING DECAL PLACEMENTThis drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, call the telephone num-ber on
20HOW TO USE AN IFIT WORKOUTTo purchase iFit cards, go to www.iFit.com or call the telephone number on the front cover of this manual. iFit cards are
21THE INFORMATION MODEThe console features an information mode that keeps track of the total distance that the walking belt has moved and the total nu
22 HOW TO FOLD THE TREADMILLBefore folding the treadmill, adjust the incline to the lowest position. If you do not do this, you may damage the treadmi
23Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further as
24 Locate the Reed Switch (33) and the Magnet (32) on the right side of the Pulley (31). Turn the Pulley until the Magnet is aligned with the Reed S
25SYMPTOM: The walking belt is not centered between the foot rails. IMPORTANT: If the walking belt rubs against the foot rails, the walking belt may b
26EXERCISE GUIDELINESThese guidelines will help you to plan your exercise program. For detailed exercise information, obtain a reputable book or consu
27 1 6 #8 x 1/2" Ground Screw 2 6 3/8" x 3 1/4" Screw 3 6 3/8" Star Washer 4 20 #8 x 3/4" Screw 5 6 M8 x 25mm
283940301832331430293141181919204544272814342014281414141411141414434611421735777725251919382424202014111414141414141414919696989868976786104410036103
294813519215161649262650501313441616955210610544455444445354EXPLODED DRAWING BModel No. PETL69911.0 R0512A
3IMPORTANT PRECAUTIONS1. Before beginning any exercise program, consult your physician. This is especially important for persons over age 35 or perso
30566767463323567968889565679269169757278787878717197269167570707063731701212679899EXPLODED DRAWING CModel No. PETL69911.0 R0512A
315862818090609382484844421645921749393938357552323856547836185881476565656565656566EXPLODED DRAWING DModel No. PETL69911.0 R0512A
Part No. 326806 R0512A Printed in China © 2012 ICON IP, Inc.This electronic product must not be disposed of in municipal waste. To pre-serve the en
420. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 7 and HOW TO FOLD AND MOVE THE TREADM
5Thank you for selecting the new PROFORM® 620 ZLT treadmill. The 620 ZLT treadmill provides an impressive selection of features designed to make your
6PART IDENTIFICATION CHARTUse the drawings below to identify small parts used for assembly. The number in parentheses below each draw-ing is the key n
71. Make sure that the power cord is unplugged. Remove and discard the two screws (A) and the shipping bracket (B) from the right side of the Base (
83. Identify the Right Upright (76), which is marked “Right.” Have a second person hold the Right Upright near the Base (74). See the inset drawing.
96. Identify the Left and Right Upright Covers (88, 89). Slide the Left Upright Cover onto the Left Upright (66) as shown. Slide the Right Upright C
Kommentare zu diesen Handbüchern